Expert Advice
Industry Leader
Made in the USA
Safe for Natural Stone
Trusted by Professionals
About the Product
Guide
Reviews
More Information
Elevate your cleaning routine with our exceptional Bath & Shower Kit. Specially curated to offer you the ultimate satisfaction of cleanliness, this comprehensive package addresses every cleaning requirement in your bath and shower areas. Its powerful composition is terrific for daily sprucing up and is just as effective against stubborn grime, soap scum, mineral build-up, mold, and mildew, leaving your surfaces sparkling after each application.
Engineered with natural stone in mind, this kit is remarkably gentle on delicate finishes. So, why wait? Upgrade to our Bath & Shower Kit and make your bath and shower areas radiate with cleanliness that’s hard to ignore!
Bath & Shower Kit includes:
- (1) Quart of MB-3 Soap & Mineral Deposit Remover
- (1) Quart of MB-5 Stone & More Multi Surface Spray Cleaner
- (1) Quart of MB-9 Mold & Mildew Remover
Preparation:
- Use rubber gloves to avoid contact with the skin.
- Dilute MB-3 Soap & Mineral in a proportion of 1 part MB-3 to 2 parts warm water with the 32oz spray bottle.
- Use MB-5 as needed before during and after MB-3 or MB-9.
- Test on a spare piece or in an inconspicuous area first.
Directions:
Step 1: MB-3
- Liberally apply with a sponge and allow to stand without letting the solution dry.
- Once the soap scum begins to break up, scrub lightly with a scrub brush or plastic scouring pad.
- Rinse thoroughly.
- Repeat these steps if necessary.
Step 2: MB-9
- Spray on liberally.
- Allow mold or mildew stains to disappear, and be careful to not allow the product to dry on the surface.
- Rinse thoroughly.
- Repeat these steps if necessary.
Step 3/As needed: MB-5
- Hold the sprayer about 6 to 8 inches from the surface.
- Spray a light mist over the area to be cleaned.
- Let the product sit for approximately 30 seconds.
- Buff the surface dry with a paper towel or a clean white cloth.
- When the towel becomes wet, discard it and start with a fresh one.
Product Description
Bath & Shower Kit includes:
(1) Quart of MB-3 Soap & Mineral Deposit Remover
(1) Quart of MB-5 Stone & More Multi Surface Spray Cleaner
(1) Quart of MB-9 Mold & Mildew Remover
MB-3 Soap & Mineral Deposit Remover is specifically designed to safely dissolve soap and mineral deposits from natural stone, tile, glass and fiberglass. MB-3 Soap & Mineral uses a unique combination of special non-acid chemicals that quickly and easily dissolve and remove dingy, unsanitary soap scum and hard water deposits from shower walls, floors, doors, wash basins, and bath tubs. It does effortlessly what can’t be done even by hard scrubbing with ordinary cleaners and abrasives. MB-3 Soap & Mineral Deposit Remover is highly effective and safe on most natural marble glossy surfaces. Be certain to test product on a spare tile or inconspicuous area for extra caution before use.
Directions for use: Use rubber gloves to avoid contact to the skin. Dilute MB-3 Soap & Mineral in a proportion 1 to 2 with warm water. Liberally apply with a sponge and allow to stand, without letting the solution dry, until soap scum begins to break up. Scrub slightly with a scrub brush or plastic scouring pad. Rinse thoroughly. Repeat process if necessary. Drying is not required.
MB-5 Stone & More Multi Surface Spray Cleaner uses a pH neutral combination of special chemicals that quickly and easily cleans marble, granite, ceramic, corian, porcelain, glass, including mirrors and most other hard surfaces. It also works great on bath and kitchen fixtures. Safe to use daily. Not designed to clean heavily soiled areas or remove soap build up. (For heavy duty cleaning and removal of soap build up, use our MB-3 Soap & Mineral Deposit Remover.)
Directions for use: Hold sprayer about 6 to 8 inches from surface, then spray a light mist over the area to be cleaned. Let the product sit for approximately 30 seconds. Buff the surface dry with a paper towel or a clean white cloth. When towel becomes wet, discard and start with a fresh one.
MB-9 Mold & Mildew Remover cleans without scrubbing. Removes mold, mildew stains, and odor on contact. Regular use (every 2 to 4 weeks, depending on level of use) will keep surfaces clean. It is safe on most natural marble surfaces. Be certain to test product first on a spare tile or inconspicuous area for extra caution before use.
Directions for use: Spray on liberally. Allow mold or mildew stain to disappear, be careful to not allow product to dry on the surface. Then rinse thoroughly. Repeat these steps if necessary. In the case of very old stubborn staining, you can use a soft brush to help break up stain. Drying is not necessary. If used on surfaces that will touch food, rinse thoroughly at least twice.
Made in the USA